.. raw:: html

.. _platform_examples: Platform Examples ================= Simple Example with 3 hosts --------------------------- Imagine you want to describe a little platform with three hosts, interconnected as follows: .. image:: /tuto_smpi/3hosts.png :align: center This can be done with the following platform file, that considers the simulated platform as a graph of hosts and network links. .. literalinclude:: /tuto_smpi/3hosts.xml :language: xml The elements basic elements (with :ref:`pf_tag_host` and :ref:`pf_tag_link`) are described first, and then the routes between any pair of hosts are explicitly given with :ref:`pf_tag_route`. Any host must be given a computational speed in flops while links must be given a latency and a bandwidth. You can write 1Gf for 1,000,000,000 flops (full list of units in the reference guide of :ref:`pf_tag_host` and :ref:`pf_tag_link`). Routes defined with :ref:`pf_tag_route` are symmetrical by default, meaning that the list of traversed links from A to B is the same as from B to A. Explicitly define non-symmetrical routes if you prefer. Cluster with a Crossbar ----------------------- A very common parallel computing platform is a homogeneous cluster in which hosts are interconnected via a crossbar switch with as many ports as hosts, so that any disjoint pairs of hosts can communicate concurrently at full speed. For instance: .. literalinclude:: ../../examples/platforms/cluster_crossbar.xml :language: xml :lines: 1-3,18- One specifies a name prefix and suffix for each host, and then give an integer range. In the example the cluster contains 65535 hosts (!), named ``node-0.simgrid.org`` to ``node-65534.simgrid.org``. All hosts have the same power (1 Gflop/sec) and are connected to the switch via links with same bandwidth (125 MBytes/sec) and latency (50 microseconds). .. todo:: Add the picture. Cluster with a Shared Backbone ------------------------------ Another popular model for a parallel platform is that of a set of homogeneous hosts connected to a shared communication medium, a backbone, with some finite bandwidth capacity and on which communicating host pairs can experience contention. For instance: .. literalinclude:: ../../examples/platforms/cluster_backbone.xml :language: xml :lines: 1-3,18- The only differences with the crossbar cluster above are the ``bb_bw`` and ``bb_lat`` attributes that specify the backbone characteristics (here, a 500 microseconds latency and a 2.25 GByte/sec bandwidth). This link is used for every communication within the cluster. The route from ``node-0.simgrid.org`` to ``node-1.simgrid.org`` counts 3 links: the private link of ``node-0.simgrid.org``, the backbone and the private link of ``node-1.simgrid.org``. .. todo:: Add the picture. Torus Cluster ------------- Many HPC facilities use torus clusters to reduce sharing and performance loss on concurrent internal communications. Modeling this in SimGrid is very easy. Simply add a ``topology="TORUS"`` attribute to your cluster. Configure it with the ``topo_parameters="X,Y,Z"`` attribute, where ``X``, ``Y`` and ``Z`` are the dimension of your torus. .. image:: ../../examples/platforms/cluster_torus.svg :align: center .. literalinclude:: ../../examples/platforms/cluster_torus.xml :language: xml Note that in this example, we used ``loopback_bw`` and ``loopback_lat`` to specify the characteristics of the loopback link of each node (i.e., the link allowing each node to communicate with itself). We could have done so in previous example too. When no loopback is given, the communication from a node to itself is handled as if it were two distinct nodes: it goes twice through the private link and through the backbone (if any). Fat-Tree Cluster ---------------- This topology was introduced to reduce the amount of links in the cluster (and thus reduce its price) while maintaining a high bisection bandwidth and a relatively low diameter. To model this in SimGrid, pass a ``topology="FAT_TREE"`` attribute to your cluster. The ``topo_parameters=#levels;#downlinks;#uplinks;link count`` follows the semantic introduced in the `Figure 1B of this article `_. Here is the meaning of this example: ``2 ; 4,4 ; 1,2 ; 1,2`` - That's a two-level cluster (thus the initial ``2``). - Routers are connected to 4 elements below them, regardless of its level. Thus the ``4,4`` component that is used as ``#downlinks``. This means that the hosts are grouped by 4 on a given router, and that there is 4 level-1 routers (in the middle of the figure). - Hosts are connected to only 1 router above them, while these routers are connected to 2 routers above them (thus the ``1,2`` used as ``#uplink``). - Hosts have only one link to their router while every path between a level-1 routers and level-2 routers use 2 parallel links. Thus the ``1,2`` that is used as ``link count``. .. image:: ../../examples/platforms/cluster_fat_tree.svg :align: center .. literalinclude:: ../../examples/platforms/cluster_fat_tree.xml :language: xml :lines: 1-3,10- Dragonfly Cluster ----------------- This topology was introduced to further reduce the amount of links while maintaining a high bandwidth for local communications. To model this in SimGrid, pass a ``topology="DRAGONFLY"`` attribute to your cluster. It's based on the implementation of the topology used on Cray XC systems, described in paper `Cray Cascade: A scalable HPC system based on a Dragonfly network `_. System description follows the format ``topo_parameters=#groups;#chassis;#routers;#nodes`` For example, ``3,4 ; 3,2 ; 3,1 ; 2``: - ``3,4``: There are 3 groups with 4 links between each (blue level). Links to nth group are attached to the nth router of the group on our implementation. - ``3,2``: In each group, there are 3 chassis with 2 links between each nth router of each group (black level) - ``3,1``: In each chassis, 3 routers are connected together with a single link (green level) - ``2``: Each router has two nodes attached (single link) .. image:: ../../examples/platforms/cluster_dragonfly.svg :align: center .. literalinclude:: ../../examples/platforms/cluster_dragonfly.xml :language: xml .. todo:: Complete this page of the manual. SimGrid comes with an extensive set of platforms in the `examples/platforms `_ directory that should be described here.